IX-22007_VKM65039_25281-25000 Belt Tensioner

Interchange Part Numbers of IX-22007_VKM65039_25281-25000 Belt Tensioner

AiX: IX-22007
SKF: VKM65039
INA: 534043010
KIA: 25281-25000
HYUNDAI: 25281-25000
GATES: T39071
FENOX: R54123
DAYCO: APV2989
OPTIMAL: 0-N2108
JAKOPARTS: J1140544
JP GROUP: 3518200209
BREDA LORETT: TOA5570

Applications of IX-22007_VKM65039_25281-25000 Belt Tensioner

2005-2010 HYUNDAI SONATA V (NF) 2.0 VVTi GLS
2005-2010 HYUNDAI SONATA V (NF) 2.4
2010-2017 HYUNDAI ix35 (LM, EL, ELH) 2.0
2010-2017 HYUNDAI ix35 (LM, EL, ELH) 2.0 4WD
2010-2012 HYUNDAI SANTA Fé II (CM) 2.4
2010-2012 HYUNDAI SANTA Fé II (CM) 2.4 4WD
2012-2017 HYUNDAI SANTA Fé II (DM) 2.4
2012-2017 HYUNDAI SANTA Fé II (DM) 2.4 4WD
2006-2017 KIA CARENS III (UN) 2.0 CVVT
2005-2017 KIA MAGENTIS (MG) 2.0
2009-2017 KIA SORENTO II (XM)2.4 CVVT
2009-2017 KIA SORENTO II (XM)2.4 CVVT 4WD
2012-2017 KIA SORENTO II (XM)2.4 GDI
2009-2017 KIA CERATO II Saloon (TD) 2.0
2009-2017 KIA CERATO KOUP (TD) 2.0
2010-2017 KIA SPORTAGE (SL) 2.0 CVVT
2010-2017 KIA SPORTAGE (SL) 2.0 CVVT AWD
2012-2017 KIA OPTIMA 2.0

Detailed Info of IX-22007_VKM65039_25281-25000 Belt Tensioner

Why should we adjust the tension force of the drive belt?
The drive belt transmits the power generated by the rotation of the motor or engine of the prime mover to the mechanical equipment with the belt wheel, so it is also called power belt.

The drive belt transfers power through friction, so the tension force of the drive belt should be adjusted to obtain appropriate friction. The friction between the drive belt and the pulley can be adjusted by adjusting the tension of the drive belt, and the tension of the drive belt can be adjusted by the tension pulley (if there is no tension pulley, then adjust the wheelbase). If the belt is too tight, the belt will be worn seriously. If it is too loose, it will cause skidding and make the belt seriously wear or even burn out. In general, when the distance between two wheels is about 1 meters, press the middle of the triangular belt with your fingers, and the belt should go down by 10-20 millimeters vertically. The tension of the belt should be inspected in the use of the belt and adjusted at any time.

Matters needing attention
1.The tension force of the tension pulley cannot be too small, otherwise, the friction between the belt and the working wheels will be small, cause skidding. Equally, the tension force of the tension pulley cannot be too large, too large tension will increase the belt load, leading to the damage of the belt and the bearing of the working wheel.
2. The tension pulley should be placed inside the loose side so that the belt is only subjected to one-way bending. At the same time, it should be as close as possible to the big wheel, so as not to affect the wrap angle of the small belt pulley. If the tension pulley is placed outside the loose side, it should be as close to the small belt pulley as possible. The size of the wheel groove of the tension pulley is the same as that of the belt pulley, and its diameter is smaller than that of the small belt pulley.